Plasma micro-cavity arrays promise low-cost, thin lighting

Dec. 19, 2011
Champaign, IL--A new micro-plasma-based approach to lighting is being commercialized by a company called Eden Park Illumination, which was founded by University of Illinois, Urbana-Champaign researchers Gary Eden and Sung-Jin Park.

Champaign, IL--A new micro-plasma-based approach to lighting is being commercialized by a company called Eden Park Illumination, which was founded by University of Illinois, Urbana-Champaign researchers Gary Eden and Sung-Jin Park. The research team was funded by the Air Force Office of Scientific Research. By confining plasma in parallel rows of micro-cavities within thin sheet materials, Eden and Park arrived at various implementations of micro-plasma arrays—some that result in inexpensive, wafer-thin, and very flexible sheets of light.

Just as in a fluorescent light, a plasma micro-cavity array (MCA) is energized by an applied voltage. In the Eden Park implementation, a sheet of aluminum foil is placed in an anodizing bath. By controlling the bath parameters, its temperature, and the time of anodizing, large arrays of micro-cavities are formed with near-optimum shape and with automatically placed interconnecting aluminum electrodes. The largest array produced so far contains a quarter million luminous micro-cavities. Thin laminated films on the surface of the wafer contain the electrical power interconnects that feed the individual cavities. When A/C power is supplied through the almost invisible grid, the array emits light.

Many gases can be used to make the micro-plasma arrays; in the process to be commercialized by Eden Park, rare gases produce ultraviolet light and specialty phosphors convert the UV into visible light, as in fluorescent lamps.

The largest arrays currently being produced are six inches square. These can be tiled together, in different colors if desired, to make larger arrays, and if desired, much larger arrays can be made, limited only by the size of the anodizing bath. Aluminum foil is used, with a thickness of 125 microns. The cavities are then sealed in very thin sheets of glass resulting in an array that is one to two millimeters thick. The plasma arrays are ruggedized to a certain extent and have an ultimate thickness of about four millimeters, leaving you with a wafer that weighs less than 200 grams.

While the efficiency of the MCA does not quite measure up to that of LEDs, there is a huge difference in thermal dissipation. MCAs generate far less heat and do not require an aluminum heat sink as LEDs do, allowing MCAs to run much cooler and be more lightweight.

SOURCE: Tech Briefs Media Group; www.greendesignbriefs.com/component/content/article/12377

About the Author

Gail Overton | Senior Editor (2004-2020)

Gail has more than 30 years of engineering, marketing, product management, and editorial experience in the photonics and optical communications industry. Before joining the staff at Laser Focus World in 2004, she held many product management and product marketing roles in the fiber-optics industry, most notably at Hughes (El Segundo, CA), GTE Labs (Waltham, MA), Corning (Corning, NY), Photon Kinetics (Beaverton, OR), and Newport Corporation (Irvine, CA). During her marketing career, Gail published articles in WDM Solutions and Sensors magazine and traveled internationally to conduct product and sales training. Gail received her BS degree in physics, with an emphasis in optics, from San Diego State University in San Diego, CA in May 1986.

Sponsored Recommendations

How to Tune Servo Systems: Force Control

Oct. 23, 2024
Tuning the servo system to meet or exceed the performance specification can be a troubling task, join our webinar to learn to optimize performance.

Laser Machining: Dynamic Error Reduction via Galvo Compensation

Oct. 23, 2024
A common misconception is that high throughput implies higher speeds, but the real factor that impacts throughput is higher accelerations. Read more here!

Boost Productivity and Process Quality in High-Performance Laser Processing

Oct. 23, 2024
Read a discussion about developments in high-dynamic laser processing that improve process throughput and part quality.

Precision Automation Technologies that Minimize Laser Cut Hypotube Manufacturing Risk

Oct. 23, 2024
In this webinar, you will discover the precision automation technologies essential for manufacturing high-quality laser-cut hypotubes. Learn key processes, techniques, and best...

Voice your opinion!

To join the conversation, and become an exclusive member of Laser Focus World, create an account today!